With Easy-Laser XT440 you can perform all necessary steps of shaft alignment on horizontal and vertically/flange mounted machines. The user-friendly software, available in 10 languages, guides you step by step through the measurement process.
See the result as a true 3D image in the display unit directly after measuring. Then evaluate the result easily with different calculation settings, for example three point reference, best fit or all positive. This can also be done directly on site without having to stop to go to a PC with separate analysis programs, which was the case previously. This makes production much more efficient.
Easy-Laser® E920 can be used to carry out all the most common geometric measurements; straightness, flatness, squareness, plumb and level. Measurement is quick and precise.
The Easy-Laser® XT290 digital precision level allows you to level your machines easily and reliably. Accuracy is guaranteed by the precision-ground, hardened steel base and precise electronics, the simplicity of quick stabilization and connection to our XT Alignment App.
Easy-Laser E980 is a laser based measurement and alignment system that helps sawmills to make optimal use of their facilities. Correctly set up machines make it possible to maintain a high rate of production with the highest quality end products hour after hour.
Easy-Laser® E970 Parallelism system use the traditional method where a laser beam is pointed alongside the machine, and then deflected 90 degrees towards the measurement object by a penta prism.
With the Easy-Laser® E930 system, pipes with diameters down to 50 mm can be measured, at a range of up to 40 m. The transmitter's laser beam can be compared to an absolutely straight and weightless ruler, that is to say a perfect starting point for precision measurement.
Easy-Laser® XT770 Shaft is the most powerful of our Generation XT laser alignment systems. The 360° Live feature gives you even more possibilities to perform advanced adjustments. With XT770 you can carry out the following:
- Align the machine
- Check base twist
- Check bearing play
- Check soft foot
- Measure machine movement over time
- Document and share the results
Easy-Laser® E960 Turbine alignment systems make the measurement and adjustment work of diapraghms and bearings easier thanks to the wireless detector unit and measurement programs that guides you through the measurement process.
Use the Easy-Laser® XT950 Bore Alignment System for accurate measuremrent of the straightness of bore centerlines, bearing journals, and other cylindrical objects.
Pre-cut, high quality, stainless steel shims, make alignment of your machines safer and easier. Choose one of our shim cases so that you always have the right shims close to hand.
- Shims of all sizes – easy to use
- Loose shims in packs of 10 – even special shims
- Shims marked with thickness – quickly identifiable
- Small, handy shim cases – easy to transport
- Burr free shims – safe to handle
When aligning with the Easy-Laser® XT190 BTA you reduce the wear on sheaves/pulleys, belts, bearings and seals, and you also get lower noise and vibration levels. The accuracy of the digital readout means that you can align within prescribed tolerances and rely on the result. Especially transmissions with two or more belts, or wide belts, are highly affected by misalignment, causing large differences in belt tensions and also increased wear and tear on edges.
The Easy-Laser® XT550 Shaft system is developed for hazardous areas and is easily operated through our XT Alignment app. It is an advanced measurement system for alignment of horizontal and vertical/flange mounted rotating machinery. With XT550 you can carry out the following:
-
Align the machine
-
Check base twist
-
Check bearing play
-
Check soft foot
-
Document and share the results
Easy-Laser® XT660 Shaft is an advanced measurement system for alignment of horizontal and vertical/flange mounted rotating machinery. With XT660 you can carry out the following:
- Align the machine
- Check base twist
- Check bearing play
- Check soft foot
- Document and share the results
Easy-Laser® E910 Flange is a system used to measure flange flatness of windmill towers, wings and hubs, tower bases, etc. It can also be used for parallelism measurement.