Condition-Based Monitoring

Valmet DNA Machine Monitoring provides condition monitoring information for process operators and maintenance personnel through one common user interface.

Condition-Based Monitoring

The PAMAS S40 AVTUR is a portable particle counter for the analysis of turbine fuels, petrol and diesel.

Condition-Based Monitoring

Portable particle counting instrument for oil-based liquids

Condition-Based Monitoring

With Easy-Laser XT440 you can perform all necessary steps of shaft alignment on horizontal and vertically/flange mounted machines. The user-friendly software, available in 10 languages, guides you step by step through the measurement process. ​

Condition-Based Monitoring

See the result as a true 3D image in the display unit directly after measuring. Then evaluate the result easily with different calculation settings, for example three point reference, best fit or all positive. This can also be done directly on site without having to stop to go to a PC with separate analysis programs, which was the case previously. This makes production much more efficient.

Condition-Based Monitoring

Easy-Laser® E920 can be used to carry out all the most common geometric measurements; straightness, flatness, squareness, plumb and level. Measurement is quick and precise.

Condition-Based Monitoring

The XT280 automatically performs vibration analysis functions based on machine running speed to help diagnose faults such as unbalance, misalignment and looseness. The system is designed to enable you to take vibration measurements from assets like pumps, motors, fans and bearings. The unit displays vibration frequency plots and allows vibration severity and bearing condition to be monitored. 

Condition-Based Monitoring

The Easy-Laser® XT290 digital precision level allows you to level your machines easily and reliably. Accuracy is guaranteed by the precision-ground, hardened steel base and precise electronics, the simplicity of quick stabilization and connection to our XT Alignment App.

Condition-Based Monitoring

Easy-Laser E980 is a laser based measurement and alignment system that helps sawmills to make optimal use of their facilities. Correctly set up machines make it possible to maintain a high rate of production with the highest quality end products hour after hour.

Condition-Based Monitoring

Easy-Laser® E710 is an alignment system that is complete in its full meaning. It does not just give you all the functions for shaft alignment, it also gives the opportunity to check the machine base and any bearing play using the standard equipment.​

Condition-Based Monitoring

Easy-Laser® E970 Parallelism system use the traditional method where a laser beam is pointed alongside the machine, and then deflected 90 degrees towards the measurement object by a penta prism.

Condition-Based Monitoring

With the Easy-Laser® E930 system, pipes with diameters down to 50 mm can be measured, at a range of up to 40 m. The transmitter's laser beam can be compared to an absolutely straight and weightless ruler, that is to say a perfect starting point for precision measurement.

Condition-Based Monitoring

The D90 belt alignment tool is attached to the sheave in a few seconds, and you can easily see the laser line projected on the targets. When the line lies in the slots of the targets, the machine is in the right position. The result is a fast, precise alignment.

Condition-Based Monitoring

Easy-Laser® XT770 Shaft is the most powerful of our Generation XT laser alignment systems. The 360° Live feature gives you even more possibilities to perform advanced adjustments. With XT770 you can carry out the following:

  • Align the machine
  • ​Check base twist
  • Check bearing play
  • Check soft foot
  • Measure machine movement over time
  • Document and share the results

Condition-Based Monitoring

Easy-Laser® E960 Turbine alignment systems make the measurement and adjustment work of diapraghms and bearings easier thanks to the wireless detector unit and measurement programs that guides you through the measurement process. 

Condition-Based Monitoring

The Easy-Laser® E950 Bore alignment system makes the control and adjustment work of bearings and bearing journals easier thanks to the wireless detector unit and measurement programs that guides you through the measurement process. All of the parts included in the systems are designed and built for even the most demanding workplace and for easy setup on any machinery.

Condition-Based Monitoring

Pre-cut, high quality, stainless steel shims, make alignment of your machines safer and easier. Choose one of our shim cases so that you always have the right shims close to hand.

  • Shims of all sizes – easy to use
  • Loose shims in packs of 10 – even special shims
  • Shims marked with thickness – quickly identifiable
  • Small, handy shim cases – easy to transport
  • Burr free shims – safe to handle

Condition-Based Monitoring

When aligning with the Easy-Laser® XT190 BTA you reduce the wear on sheaves/pulleys, belts, bearings and seals, and you also get lower noise and vibration levels. The accuracy of the digital readout means that you can align within prescribed tolerances and rely on the result. Especially transmissions with two or more belts, or wide belts, are highly affected by misalignment, causing large differences in belt tensions and also increased wear and tear on edges.

Condition-Based Monitoring

The Easy-Laser® XT550 Shaft system is developed for hazardous areas and is easily operated through our XT Alignment app. It is an advanced measurement system for alignment of horizontal and vertical/flange mounted rotating machinery.​ With XT550 you can carry out the following:

  • Align the machine
  • Check base twist
  • Check bearing play
  • Check soft foot
  • Document and share the results

Condition-Based Monitoring

Easy-Laser® XT660 Shaft is an advanced measurement system for alignment of horizontal and vertical/flange mounted rotating machinery. With XT660 you can carry out the following:

  • Align the machine
  • ​Check base twist
  • Check bearing play
  • Check soft foot
  • Document and share the results

Condition-Based Monitoring

Easy-Laser® E910 Flange is a system used to measure flange flatness of windmill towers, wings and hubs, tower bases, etc. It can also be used for parallelism measurement.

Condition-Based Monitoring

Fluid analysis provides a snapshot of what is happening inside your equipment. It tells you the condition of the fuel or lubricant and identifies component wear and contamination. The Donaldson Patch Test Kit allows you to conduct on-site particulate analysis in as little as ten minutes. It quickly and reliably assigns a three-digit cleanliness code per ISO 4406-1999 to a given fluid sample.

Condition-Based Monitoring

The VIBER X4™ is a cutting-edge route-based vibration analyzer designed for enhanced condition monitoring and top-notch accuracy.

Condition-Based Monitoring

Repair and maintenance professionals will benefit from VIBER X3™. It's a unique situation.
Excellent condition monitoring gadget that is simple to use and dependable.

Condition-Based Monitoring

Maintenance and repair professionals will benefit from VIBER X2 . It's a fantastic tool for basic conditions.
Monitoring tests that are simple to use and dependable for analyzing status. The VIBER X2 ProTM instrument offers the following features:

  • Accurate measurements for 4 selectable frequency ranges. Gives high reliability.
  • Real-time measurement of the total vibration level and the Bearing Condition (BC) measures and displayed simultaneously, facilitates analysis of bearing faults.
  • Fast and easy fault analysis screen displaying the five highest peaks with amplitude and frequency one by one.

Condition-Based Monitoring

VIBER X1 ™ measures the effective velocity (mm/s RMS)in the frequency range 2–maximum frequency. This range covers most of the frequencies that will occur for the majority of mechanical failures and imperfections. Examples are balance, looseness, resonance, misalignment of shafts and gears, cavitations, and other fl uid-generated vibrations. The judgments of the measured levels are supported by several vibration standards.

Condition-Based Monitoring

VIBER X™ This is a significant step toward well-planned equipment maintenance.
Because of the Route feature in X-Viber, measurements are quick and simple.
The same equipment is used to measure the vibration level, temperature, and RPM.
This makes the measurements easier.

Balancing, Spectrum measurement and Analyzing are also possible with X-Viber.
For balancing, a balancing kit is available.
Features:

  • Route via X-Trend software.
  • Total Level.
  • Envelope.
  • Bearing Condition Value
  • Analysis
  • Temperature
  • Speed
  • Off Route Spectrum
  • Single Plane Balancing
  • Spectrum in Route (option)

Condition-Based Monitoring

With only one touch, you may perform spectrum analysis, record, snap photographs, and take temperature measurements!

Condition-Based Monitoring

The Ultimate digital ultrasonic inspection equipment with sound recording for analysis and condition monitoring.